A full van wrap is the most visible marketing your business has - and in Wolverton, we design, print and fit them at your premises, so there's no downtime dropping your van off.
A full van wrap means every panel is covered: sides, bonnet, roof, rear doors and pillars. It gives you a continuous, printed finish rather than individual cut-out letters or partial graphics. Because the design runs across the whole vehicle, there's no bare paintwork showing and no compromise on where your artwork can go.
We handle design and print in-house, which means the artwork is produced to match your actual van's panel layout before the print run starts. We travel to you, so the fitting happens at your site in Wolverton or wherever the van is based. That matters if you can't afford to have a work van sitting somewhere else for a day.
Not all wrap vinyl is the same, and understanding the differences helps you make a sensible choice rather than just picking the cheapest quote.
Wrap films fall into two broad categories based on how they are manufactured: cast vinyl and calendered vinyl. The difference comes from the production process, and it affects how the material behaves on a van over time.
Cast vinyl is made by spreading a liquid vinyl compound onto a casting sheet and curing it. The resulting film is thin, dimensionally stable and conformable - meaning it can be worked around compound curves and deep recesses without the material trying to spring back.
Why it's used for full van wraps:
Honest drawbacks:
Calendered vinyl is made by rolling and pressing vinyl compound to a set thickness. It is stiffer than cast film, less conformable, and less dimensionally stable over time. It is also significantly cheaper to buy.
Where it can work:
Where it causes problems:
For a full van wrap that covers every panel and is intended to last several years on a working van, cast film is the appropriate material. If a quote looks very low for a full wrap, it is worth asking which type of film is being used.
Once the base material is decided, the printed surface is laminated before fitting. The laminate serves two purposes: it protects the print from abrasion and washing, and it determines the visual finish of the finished wrap.
Specialist finishes such as textured laminates or metallic effects are possible but add cost and complexity. For most trade vans, a standard gloss or satin laminate does the job well.
A partial wrap covers selected panels - typically the sides and rear - leaving the bonnet and roof in original paint. It costs less than a full wrap and can still look strong if the van's paintwork is in good, consistent condition. The limitation is that the original paint must closely match the design's background colour, or the join will be visible.
A full wrap removes that constraint entirely. It also protects the original paintwork across the whole vehicle, which has a practical value if you are keeping the van for several years or will need to return it unmarked at the end of a lease. If the van's paint is already marked, dented or uneven in colour, a full wrap is usually the more sensible option.
Design and print are both done in-house. That means the artwork is produced on a template matched to your specific van make, model and year, so panel edges, door breaks and body contours are accounted for in the layout before anything is printed. Changes during design don't involve a third-party studio or additional delays.
Fitting is done at your premises or any agreed location in or around Wolverton. The van needs to be clean and dry, ideally inside a covered space if possible, as cold or wet conditions affect how vinyl applies.
We also carry out wrap removal. If you're rebranding, returning a lease vehicle or selling the van, we can remove the existing wrap cleanly. Vinyl that has been left on well beyond its working life becomes brittle, so earlier removal is easier and less likely to affect the paintwork underneath.
To give you a useful figure, we need the van make, model and year, what you're after in terms of design and coverage, and whether you have artwork ready or need us to design from scratch. Call us with those details and we'll give you a straight quote.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.