Getting great graphics on your lorry or HGV near Wootton is only half the job - here's what you need to do afterwards to keep them looking right for as long as possible.
Full-colour graphics and vinyl lettering can be applied to lorries, artics and HGVs, wherever they operate. That includes everything from individual cab door text to full printed trailer wraps. We design and print in-house and come to your premises to do the installation. We also remove old graphics when vehicles are being refreshed or returned.
Once the graphics are fitted, what happens next is largely down to how the vehicle is used and maintained. Good aftercare makes a real difference to how long the graphics perform and how clean the installation looks month to month.
Vinyl needs time to cure fully after application. In the first few days, the adhesive is still bonding to the substrate, and the film itself is settling into any curves or recesses. During this period, avoid pressure washing, jet washing or any high-pressure water contact. A light rinse with a low-pressure hose is fine if the vehicle is genuinely dirty, but leave the graphics alone if you can.
Avoid folding, rolling or creasing any flexible surfaces (such as curtain sides) more aggressively than normal during this window. The bond is developing and mechanical stress during the curing period can cause edges to lift prematurely.
HGVs pick up road dirt, diesel soot, salt and grime at a different rate from vans, particularly in autumn and winter. Keeping the graphics clean is not just cosmetic - built-up grime and salt accelerate the breakdown of the film and the adhesive layer underneath.
Hand washing is the safest option. Use warm water, a mild detergent and a soft cloth or sponge. Work from the top down. Pay attention to edges and seams, where dirt collects and can work its way under the film if it isn't removed regularly.
Automated truck washes are common for HGV fleets, and most are acceptable for graphics provided the brushes are in good condition and the pressure isn't excessive. Worn or stiff brushes can scuff and abrade the film surface over time. If a vehicle goes through an automatic wash regularly, check the graphics monthly for early signs of edge lifting or surface scratching.
Jet washing is the main cause of premature graphic failure. High-pressure water directed at graphic edges forces water underneath the film and breaks the adhesive bond. If you use a pressure washer, keep it at a low setting, hold it at least 30cm from the surface, and never direct it at edges or seams at an angle. The same applies to steam cleaning.
Diesel, oil and certain cleaning chemicals degrade vinyl film. Fuel splashes on curtain sides or trailer panels are common, particularly around filling points. Wipe these off promptly with a clean cloth. Don't use solvent-based cleaners, petrol, white spirit or any product not designed for use on vinyl - these will cloud, soften or shrink the film.
Some fleet cleaning products are formulated to be safe on wraps and graphics. If your depot uses a contract cleaning service, it's worth checking with them that the products they use are compatible with vinyl films. A short conversation can save a costly re-print.
Build a quick visual check of your HGV graphics into your existing vehicle walk-around routine. You're looking for:
Catching these early is the difference between a small localised repair and a section that has to be replaced. An edge that lifts 5mm and is left for a month in wet weather will be lifting 50mm by the time someone acts on it.
If a vehicle is being stood for a period, try to position it out of direct sun if storage allows. UV exposure degrades vinyl over time, and prolonged stationary exposure in one position concentrates that degradation unevenly. This isn't always possible at a busy depot, but it's worth considering when you have the choice.
Cover any areas of the graphics with masking or protective film if the vehicle is undergoing bodywork or repair work nearby. Paint spray, grinding dust and welding spatter all cause damage that is difficult or impossible to reverse.
Minor edge lifting caught early can often be re-adhered without replacing the full panel. If you spot a problem developing, contact us and describe what you're seeing. We'll tell you honestly whether it's something to monitor, something to repair promptly, or something that indicates a wider issue with the installation or the substrate beneath.
Vehicles near Wootton can book a check visit at their premises. If a larger section needs to be reprinted and replaced, we handle that as part of an ongoing refresh rather than a full installation from scratch where possible. Call us to talk through what you're seeing before it develops into a bigger job.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.