Getting van graphics fitted in Wootton is just the start - how you look after them from that point determines how long they stay looking sharp and how much value you get from the investment.
Van graphics apply vinyl film - either cut to shape or digitally printed - directly to your vehicle's exterior panels. The result can be as simple as your business name and number in a single colour, or as elaborate as a full-colour printed wrap covering every panel. Either way, once the film is on the van, it's exposed to whatever the working day throws at it: road grime, rain, frost, cleaning chemicals, UV light and the occasional physical knock.
None of those things will wreck a good set of graphics overnight. But they will degrade them faster than necessary if you don't pay any attention to maintenance. The good news is that keeping van graphics in decent condition doesn't require special equipment or much time - it just requires knowing what to do and what to avoid.
Road grime, diesel exhaust deposits and traffic film are mildly abrasive and chemically active. Left to build up over weeks, they work their way under the edges of vinyl film and weaken the adhesive bond. Regular washing is the single most effective thing you can do to extend the life of your van graphics.
Hand washing with a soft cloth or sponge and a mild, pH-neutral vehicle shampoo is the safest approach. You don't need anything specialist - a basic car shampoo that doesn't contain wax is fine. Rinse thoroughly and dry with a clean cloth or chamois to avoid water spotting on the film surface.
A common problem with hand washing is using the same cloth or sponge that you used on the lower sills and wheel arches on the upper panels where the graphics sit. That transfers grit directly onto the film and causes fine scratching. Use a separate cloth for different sections of the van.
Brushed roller washes are hard on vinyl graphics, particularly at the edges of panels and around any areas where the film meets a recess or trim piece. The mechanical action can lift edges that are even slightly less than perfectly bonded, and the high-pressure pre-rinse jets on some machines can get under film if directed at a low angle to an edge.
Touchless (jet-wash only) automatic washes are safer, but the cleaning chemicals used in them vary widely. Some are quite alkaline, which over time can dull printed graphics and affect the adhesive. If you use a touchless wash, rinse with plain water afterwards if you can.
The safest rule is to hand wash when you can and use automatic washes only when time doesn't allow anything else.
A pressure washer is fine for van graphics provided you use it correctly. The main risks are holding the lance too close to the surface, using too high a pressure setting, and - most critically - directing the jet at a shallow angle to any edge of the film. Water forced under a graphic edge at pressure will lift it. Keep the jet perpendicular to the panel surface, maintain at least 30 centimetres of distance, and use a fan tip rather than a pencil jet. Never jet directly at a wrap edge, a seam or anywhere the film terminates against a trim piece or rubber seal.
These three are worth treating as emergencies rather than waiting for the next wash. Bird droppings are acidic and will etch into the surface of printed film if left in warm conditions. Tree sap hardens and becomes very difficult to remove without solvents once it's dried. Fuel - particularly if it runs down a panel during filling - can attack vinyl adhesive if left in contact.
Blot rather than rub when removing anything sticky or corrosive. Rubbing spreads the contamination and can scratch the film surface. Warm water and a soft cloth will lift most things if you get to them quickly. For hardened sap or stubborn marks, isopropyl alcohol applied to a cloth (not sprayed directly) will usually work without damaging the film, but test on a less visible area first.
The areas around the fuel filler cap, door handles and door edges take more wear than the main flat panels. Repeated contact with hands, keys and fuel nozzles gradually abrades the film. These are the areas most likely to show lifting or wear first, and they're worth checking periodically. If a small lift appears at an edge, it's often possible to press it back down cleanly if you catch it early. Left to grow, a lifted edge catches everything - cleaning cloths, jacket zips - and the damage spreads.
Some fitters use small over-laminate patches at high-wear points as part of the installation. If yours didn't, ask whether this can be added at the edge areas that are showing wear.
Extended parking in direct sunlight accelerates the fading of printed graphics, particularly on the roof and any south-facing panels. If you have the choice, park in shade or under cover. This matters most with printed full-colour graphics - cut vinyl in solid colours is more resistant to UV than inkjet-printed film.
Frost doesn't directly damage vinyl film, but trying to remove ice from a wrapped panel with a hard plastic scraper will. Keep an ice scraper away from graphics areas. A de-icer spray is safer, but rinse it off with clean water once the ice is clear rather than leaving the chemical on the surface.
If you notice lifting at a seam or panel edge, a bubble that wasn't there before, or a section of film that's starting to look hazy or discoloured, it's worth getting a professional opinion before the problem gets worse. Some issues - particularly early-stage edge lifting on otherwise sound graphics - can be sorted quickly and cheaply. The same problem ignored for another six months may mean replacing the whole panel rather than just re-securing an edge.
We come to customers in and around Wootton, so we can take a look at your van at your premises and tell you honestly whether something needs attention or whether it's nothing to worry about.
Even well-maintained graphics have a lifespan. When the time comes to remove them - whether because the design has changed, the van is being sold, or the film has simply done its time - removal should be done carefully to avoid damaging the paint underneath. We offer removal as part of our service. Trying to pull old, hardened film off in a hurry is one of the more common ways people damage a van's paintwork unnecessarily.
If you've recently had graphics fitted, or you're thinking about getting some done in Wootton, call us and we'll talk you through what your specific installation needs in terms of upkeep. Different materials and finishes have slightly different requirements, and knowing what applies to your van specifically is more useful than general advice.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.