If you want to brand specific panels on your van without committing to a full wrap, a part wrap in Kingsthorpe is a practical, cost-effective way to put your business in front of local customers every day.
A part wrap means vinyl is cut and applied to specific panels of your vehicle - rear doors, side panels, bonnet, roof section or any combination - rather than covering every surface. The result is a clean, professional finish that carries your logo, contact details, colours and any other branding you choose. The uncovered paintwork is left untouched.
Part wraps sit between simple cut vinyl lettering and a full vehicle wrap in terms of coverage and cost. For tradespeople and small fleet operators who want strong visual impact without the outlay of a full wrap, they are often the right call.
There is no shortage of people offering van wrapping. The gap between a well-applied part wrap and a poor one is significant, and it shows quickly. Here is what to focus on when you are deciding who to use.
Some installers outsource the print work to a third party and simply apply what arrives. When design and print happen under one roof, any error in colour, sizing or layout is caught before the vinyl is cut. We design and print in-house, which means the file we install is the file we checked ourselves. Ask any installer where the print comes from and who handles artwork corrections if something is wrong.
Your van is a working vehicle. Time off the road costs money. We travel to your premises or location and carry out the installation there, so your vehicle does not need to be dropped off and collected. Ask where the work will be done and whether you need to make other arrangements to get your van to them.
Any contractor working on your vehicle should be insured. Ask any contractor to confirm that before they start. If an installer cannot confirm insurance plainly, treat that as a reason to look elsewhere.
Ask to see recent examples of part wraps specifically, not just full wraps or printed signage. Look at the edges around door handles, panel joins and curves. That is where application quality shows. Poor preparation or incorrect material choice causes peeling at edges within months. A well-applied wrap on a properly cleaned and prepared surface should stay put through ordinary use.
Before you sign off on a job, run through these questions. The answers will tell you a great deal about how the contractor works.
Part wrap pricing varies depending on how many panels are covered, the complexity of the design and the type of vehicle. A single rear door panel on a transit-sized van will cost considerably less than both sides plus the bonnet. As a rough guide, part wraps for vans in the Northampton area typically start from around £200-£300 for a simple single-panel job and rise to £600-£900 or more for a larger multi-panel installation with a detailed design.
Be cautious of very low quotes. The cost of quality cast vinyl film and the time needed to apply it properly to curved surfaces means there is a floor below which corners are being cut somewhere - usually on material quality, preparation time, or both.
When you get a part wrap done properly, you are paying for artwork, colour-accurate printing, correctly specified material for the panels being covered, thorough surface preparation, careful installation around recesses and joins, and a finish that looks professional from the roadside. You are also paying for the fact that it will not start peeling from a door recess three months later.
A cheap job that starts lifting at the edges is not just an eyesore - it reflects directly on your business in the eyes of every customer and neighbour who sees your van parked on their street.
Not every van needs to be wrapped from roof rail to sill. Many of the most effective commercial vehicle graphics use just two or three panels. Both rear doors visible at a junction, or a large side panel graphic seen from a pavement, can generate as much recall as a full wrap at a fraction of the cost. The key is a clean, readable design with good contrast, applied to the panels most visible in the situations your vehicle is parked in most often.
If you are unsure which panels would work hardest for your type of work in Kingsthorpe and the surrounding area, that is a conversation worth having before you commit to a layout. A good installer should be able to advise based on your trade and how your van is typically used.
Call Van Wrapping Northampton to talk through what you need. Tell us your vehicle make, what panels you are thinking about, and what you want the wrap to say. We will advise on the right approach and give you a clear price before anything is agreed.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.