Covering Northampton and the surrounding area Monday to Friday 9:00am - 5:00pm Get a quote

Full Van Wraps in Kettering

If your van's livery is peeling, fading, or simply no longer doing its job, a full wrap from Van Wrapping Northampton is the most effective way to put it right - and we come to you in Kettering to do it.

5.0 from 9 Google reviews Est. 2020 Quoted in writing first Nothing printed until you sign off the proof Fitting arranged at your site

When a full van wrap is telling you something is wrong

A full van wrap should look sharp and stay flat for years. When it starts to fail, it rarely fails quietly. Knowing what to look for - and what has actually caused the problem - helps you decide whether a repair is worth attempting or whether you need a fresh wrap from scratch.

The most common visible warning sign is lifting at the edges. Vinyl loses its bond at corners, door shuts, and panel edges first, because those areas flex the most and because surface preparation is hardest to get right there. Once a corner lifts, water gets underneath, the adhesive breaks down further, and the lift spreads quickly. A small lifted edge is a signal, not a cosmetic flaw you can ignore.

Bubbling and tunnelling

Bubbles that appear shortly after fitting usually mean trapped air or moisture that was not fully worked out during installation. Bubbles that appear months later are a different matter. They typically mean the vinyl has delaminated from the paint because the surface underneath was not clean enough, or because a low-grade film was used that lacks the conformability to stay bonded on curved panels over time.

Tunnelling - raised ridges running in a line across a panel - happens when the vinyl has shrunk. Cast vinyl films are made to hold their dimensions; cheaper calendered films are not, and they will shrink as they age, creating tension lines that pull away from the surface. If you see tunnelling on a wrap that was not fitted by us, that is usually a sign the material used was not suited to a full vehicle application.

Fading and colour shift

Printed wraps fade. How quickly depends on the quality of the print inks, the laminate applied over the top, and how much direct sun the van is parked in. A wrap that is fading unevenly - darker on the sides than the roof, for example - usually means the laminate failed in one area, allowing UV to attack the ink directly. Uneven fading on a wrap that is only two or three years old is a sign the print or laminate was not up to standard. Good-quality printed vinyl with a proper overlaminate should hold its colour significantly longer than that under normal UK conditions.

Cracking and brittleness

Vinyl becomes brittle with age and UV exposure. When it cracks rather than stretching around panel details, it has reached the end of its life. Trying to remove brittle vinyl is a slow job because it breaks into small pieces rather than peeling cleanly. If your current wrap is cracking, factor that into your removal timeline - the older and more brittle the material, the more labour the removal takes.

What causes wraps to fail early

Poor surface preparation is the leading cause of premature failure. Paint that has not been degreased and cleaned properly will not hold the adhesive. Any wax, polish or silicone contamination - even from a recent car wash - will cause lifting. Panel dents or rust that have been filled and respray-painted can cause adhesion problems if the new paint was not fully cured before wrapping.

Incorrect material choice is the second most common cause. A full wrap is a large surface area with compound curves, door handles, gutters and hinges. It needs a cast vinyl film with the stretch and memory to conform without lifting. Using a calendered film - the type suited to flat signboards - on a vehicle is a false economy. It will shrink and lift within a year or two.

Installation temperature matters too. Vinyl applied in very cold conditions becomes stiff and difficult to stretch into recesses, and the adhesive does not bond as well. Work done in a cold yard in January is higher risk than work done in a controlled indoor space. When we come to you in Kettering, we assess the conditions before we start and will advise if anything needs adjusting.

Damage that looks like a wrap problem but isn't

Stone chips and scratches that have gone through the vinyl to the paint beneath will allow water to track under the film from the entry point. This can cause lifting over a large area that appears unrelated to the chip itself. The wrap has not failed - it has been breached - but the result looks similar. Check for entry points like this if lifting is appearing in the middle of a panel rather than at the edges.

Pressure washing at close range or with a narrow-angle jet will force water under the edges of a wrap and lift it. Wraps are not designed to withstand a jet directed along the film edge. Touchless washes and wide-angle rinsing are safer. If your wrap has been high-pressure washed regularly, that may explain edge lifting that otherwise looks like an adhesion failure.

When to call us rather than wait

Small lifted edges can sometimes be re-bonded with low-heat and careful application. That is a minor remedial job. Widespread lifting, bubbling across multiple panels, tunnelling or cracking means the wrap has reached the point where a full replacement is the right decision. Continuing to drive with a failing wrap means the loose material is exposed to wind at speed, which accelerates the delamination and makes eventual removal harder.

We carry out wrap removal as well as new installations, and we will give you an honest assessment of what you are dealing with before any work starts. If your van is in Kettering, call us to arrange a look at the vehicle at your premises or yard.

Full van wraps: what you get

A full wrap covers every panel - bonnet, roof, all four sides, doors, tailgate and door shuts. We design and print everything in-house at our Northampton base, which means we control the colour accuracy and print quality directly. We then come to you to fit the wrap, so your van does not need to travel to us. It is worth asking any installer whether they are insured before you book. All the work is done at your premises or a location that suits you.

Full wraps are available for all common van sizes: car-derived vans, medium panel vans and large Sprinter-type vehicles. If you are running a small fleet in Kettering and want consistency across multiple vehicles, speak to us about batch pricing and scheduling to minimise the time any single van is out of action.

To get the process started, call us and describe your van - make, model, age and current condition. That gives us what we need to come back to you with an accurate quote.

Why use us in Kettering

  • Your design shown on your vehicle before printing.
  • Graphics designed and printed by us.
  • We fit at your premises in Kettering.
  • We are insured.

Full Van Wraps in Kettering?

Phone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.

Call Quote