Covering Northampton and the surrounding area Monday to Friday 9:00am - 5:00pm Get a quote

Lorry and HGV Graphics in Kettering

If your lorry or HGV is out on the road around Kettering and nobody can tell who it belongs to, that is marketing spend going to waste every mile.

5.0 from 9 Google reviews Est. 2020 Quoted in writing first Nothing printed until you sign off the proof Fitting arranged at your site

When Your Fleet Graphics Start Letting You Down

Most operators don't notice a problem with their HGV graphics until someone else points it out. By then the vinyl has been deteriorating for months, and the professional image the livery was meant to project has quietly slipped away. Knowing what to look for means you can act before the damage to your brand becomes obvious to every driver and business owner who passes your vehicle on the road.

The signs are usually gradual. A full trailer wrap or cab-door lettering that looked sharp when it was first fitted will start to show its age in predictable ways, and understanding why each one happens helps you decide what action to take.

Warning Sign 1: Lifting Edges and Peeling Corners

Vinyl graphics bond to the vehicle panel through a pressure-sensitive adhesive. When that bond weakens, the edges are the first place to go. You'll notice a corner starting to curl, or a seam lifting where two panels of film meet. Left alone, this allows moisture and road dirt to get underneath, which accelerates the peel and can stain the paintwork below.

The most common cause is poor surface preparation at the time of fitting. If the panel wasn't degreased and cleaned properly before the vinyl went on, the adhesive never bonded fully to begin with. It can also happen if graphics were applied in cold conditions without allowing the adhesive enough time to cure. A vehicle that goes through a commercial wash regularly will put added stress on edges that were never properly sealed.

What to do: if the lifting is minor and caught early, it may be possible to re-seal the edge. If the adhesive has dried out or the film has stretched, that section will need replacing. Don't leave it - a 10 cm peel can become a full panel loss inside a few weeks of motorway running.

Warning Sign 2: Fading and Colour Shift

Print inks on vehicle graphics are exposed to UV radiation every day the vehicle is in use. Quality cast vinyls with UV-resistant laminates hold their colour for several years, but cheaper calendered films without a protective overlaminate can begin to fade noticeably within twelve to eighteen months. Reds and yellows tend to fade fastest; blues and greens usually hold longer.

Colour shift is a subtler problem. If your fleet runs multiple vehicles and the graphics were printed at different times, you may notice that the same corporate red looks slightly different from one cab to another. That inconsistency is often more damaging to brand perception than outright fading, because it looks like you don't have control of your own standards.

Fading is not reversible. Once the inks have gone, the only fix is replacement. When you're pricing new graphics, ask what laminate is included - an overlaminate is not optional for a vehicle that runs year-round.

Warning Sign 3: Bubbling and Silvering

Bubbles under a wrap are almost always a sign of trapped air or moisture. A small bubble that appears shortly after installation is usually an application issue - air that wasn't fully squeegeed out. These can sometimes be worked out if caught very early. Bubbles that appear months or years after fitting point to something different: moisture has found its way under the film, often through a micro-crack in the laminate or a compromised edge.

Silvering is a related problem. It refers to a milky or silver-tinted haze that appears under the film, usually in patches. It's caused by adhesive failure combined with moisture ingress, and it tends to appear first around rivets, panel joints and any point where the film was cut and exposed. On curtainsider trailers with large rivetted panels, this is a known weak point - the vinyl has to conform around each rivet head, and those points are more vulnerable over time.

Warning Sign 4: Cracking and Brittleness

Vinyl film has a lifespan. As it ages, the plasticisers in the film gradually migrate out, leaving the material stiffer and more brittle. You'll see this as hairline cracks, usually running along panel edges or across large flat areas that flex slightly as the trailer moves. Once a film is cracking, it cannot be repaired - the whole section needs to come off.

Brittleness also makes removal harder and more expensive. Old, cracked film breaks into small pieces rather than peeling cleanly, which means significantly more labour to strip the vehicle back to bare metal before new graphics can go on. If your graphics are ageing, factor that into your timing - removing them before they become brittle keeps the job cleaner and cheaper.

Warning Sign 5: Damage from Incorrect Washing

Jet washing at high pressure, particularly with a narrow-angle nozzle aimed directly at a graphic edge, is one of the most common causes of premature lifting. Automated brush washes can also catch raised edges and start a peel. This is worth raising with whoever manages your wash schedule - the technique matters as much as the frequency.

Solvent-based cleaning products applied to vinyl graphics will attack the laminate and can cloud or discolour the print. Only mild, non-solvent detergents should be used directly on graphics.

What Causes Graphics to Fail Prematurely?

Setting aside age and normal wear, the main causes of early failure are:

  • Inadequate surface preparation before fitting - contamination left on the panel prevents proper adhesion
  • Wrong film choice for the application - a cheap, short-life film used on a vehicle expected to run for five or more years
  • Application in poor conditions - very cold or very humid environments affect adhesive performance
  • Fitting to damaged or rusty panels - vinyl applied over rust or filler will lift as the substrate continues to deteriorate beneath it
  • No overlaminate - without a UV-protective laminate, print life is significantly shortened
  • Poor edge sealing at cuts and joins

Lorry and HGV Graphics Fitted at Your Premises in Kettering

We come to you. Whether your lorries are based at a yard or depot in Kettering or they're only available between runs, we work at your location rather than asking you to bring vehicles to us. We design and print in-house, which means we control the quality from artwork to finished panel - there's no outsourcing the print and hoping the colours match what was approved.

If you've got existing graphics that need to come off before new ones go on, we handle removal as well - including the more stubborn jobs on older vehicles.

If you're seeing any of the warning signs described above on your HGVs or artics, give us a call and we'll take a look at what you've got and tell you honestly what needs doing.

Why use us in Kettering

  • Your design shown on your vehicle before printing.
  • Graphics designed and printed by us.
  • We fit at your premises in Kettering.
  • We are insured.

Lorry and HGV Graphics in Kettering?

Phone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.

Call Quote