If you've never had a van part-wrapped before, knowing what to expect from the first conversation to driving away makes the whole thing much easier to plan around.
A part wrap applies vinyl to chosen panels of your van - rear doors, side panels, bonnet, cab doors or roof - rather than covering the whole vehicle. It's a cost-effective way to brand your van professionally without the full-wrap price. For tradespeople in Rushden, it means your name and number are on the road every day without a large upfront spend.
Understanding exactly how the job is done - from initial contact through to the finished result - helps you plan the timing, prepare your vehicle properly and know what a good job should look like.
Getting an accurate quote starts with a few specific details. The more you can give us upfront, the more useful our response will be.
Once we have this, we can give you a proper quote rather than a ballpark figure.
If you need a design, we work from your brief - your logo files, any brand colours, the information you want on the van (name, number, website, trade) and any preferences about layout or style.
We produce a visual for your approval before anything gets printed. This is your chance to check that the layout works, the colours look right and the contact details are correct. Mistakes caught at the design stage cost nothing to fix. Mistakes spotted after the vinyl is printed and fitted are expensive.
If you're supplying your own artwork, it needs to be at the right resolution and in the correct format for large-format print. If you have a logo that was only ever made for web use, it may need redrawing at a larger scale - we can advise on this during the enquiry stage.
We print everything ourselves, which means we're not waiting on a third-party printer and we can quality-check the output before it leaves our hands.
We come to you - the job is done at your premises in or around Rushden. When we arrive, the first thing we do is inspect the panels that are being wrapped.
Surface preparation is the most important step in a part wrap and the one most often rushed on cheap jobs. Any contamination between the vinyl and the paintwork - wax, polish, grease, road film, even silicone from tyre dressings - will prevent the adhesive from bonding properly and cause early lifting.
We clean and degrease every panel before the vinyl goes on. If a panel has existing graphics, we remove them and clean off any adhesive residue. The panel needs to be fully clean and dry before the film is applied.
It's worth checking your van before we arrive. If it has just been waxed or polished, let us know - some products need more time and product to remove fully. A van that's been pressure-washed and left to dry is in good shape for us to start on.
If there's existing vinyl on the panels, it comes off before anything new goes on. The method depends on the age and type of the existing film. Older vinyl can be brittle and more likely to leave adhesive residue. Newer film generally releases more cleanly.
Adhesive residue left after removal needs to be fully cleared before the new vinyl is applied. Any residue under the new film will cause bubbling or lifting. This takes time to do properly and is part of what separates a tidy job from one that starts failing within months.
With the panels clean and prepared, the vinyl is applied panel by panel. The process involves positioning the film, removing the backing, and working the vinyl onto the surface using squeegees to push out air and ensure full contact between the film and paintwork.
Edges and seams get particular attention. This is where failures start - if the film isn't pressed down firmly at every edge and around any recesses, rivets or mouldings, water and dirt get in and the adhesive lets go from the outside. Around door handles, light clusters and panel breaks, the vinyl is trimmed precisely so edges are clean and sealed.
On complex surfaces - curved bonnets, wheel arch lips, areas around vents - the film may need to be heated and stretched slightly to conform without creasing. This requires care; too much heat degrades the film, too little leaves stress in the material that causes lifting over time.
A larger job covering multiple panels on a full-size van will take longer. We'll give you a realistic time expectation when we quote.
Once the vinyl is on, we inspect every panel before we're done. We're looking at edges, seams, any areas around mouldings or rivets, and the overall finish of the print or colour. Any small air pockets that weren't worked out during application are attended to at this stage.
You should walk around the van and look at the finished result yourself before we leave. Check that your contact details are correct, the design looks as expected, and there are no visible imperfections in the finish. If anything isn't right, say so. It's much easier to address before we pack up than after.
Fresh vinyl needs a short settling period before it can be washed. We'll tell you how long to leave it. When you do wash the van, hand washing or a contactless wash is better than a brush wash. Pressure washers used directly at panel edges will force water under the film over time and shorten its life.
Avoid applying wax or polish directly over the vinyl - it makes future removal harder and can affect the film's surface over time.
Tell us your vehicle, the panels you want wrapped and whether you have artwork ready. We'll come to your Rushden premises to do the work. Call Van Wrapping Northampton to get a quote and book a convenient time.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.