If you have never had a van wrapped before, here is exactly what happens from the moment you get in touch with us to the moment your van leaves with the finished livery in Rushden.
Everything starts with a conversation about your van, your business and what you want the finished result to look like. We need to know the make, model and year of the vehicle because panel shapes, door configurations and the position of handles, hinges and vents all vary. A Transit Custom and a Sprinter are wrapped differently, and the same design may need adjusting to work around each vehicle's specific profile.
At this stage we also talk about what you want on the van: a full colour change, a printed design with your brand, partial graphics, or just cut lettering. Each option has a different price point and production process, and knowing your brief up front lets us give you an accurate cost rather than a rough figure that changes later.
We design in-house. Once you have confirmed the direction, we work up a design proof scaled to your van's template. Vehicle templates show the exact panel layout, handle positions, door lines and character lines of your specific van model, so what you approve on screen maps accurately to the physical vehicle.
Colour choices, font sizes and the placement of logos and contact details are all reviewed at this stage. It is worth taking time here: a phone number that is too small to read from a following car, or a logo placed over a door handle, are problems fixed cheaply on a proof but expensively once the film is printed and cut.
We provide proofs for your review and make adjustments before anything goes to print. You should not be looking at the finished film for the first time on your van.
Once the design is approved, we print in-house on wide-format printing equipment. The vinyl film is printed, then an overlaminate is applied over the entire print surface before cutting. The laminate protects the inks from UV light and weathering and gives the finished wrap either a gloss or matt surface, depending on what was agreed at the design stage.
Printed panels are then cut to size, either by machine (for precision repeatable shapes) or by hand where the design requires it. Cut lettering and simple graphics go through the same lamination and cutting process. The film is then kept flat and clean until installation day.
This step is where a lot of cheaper wrap jobs go wrong. The vehicle surface must be spotlessly clean and free of any contamination before film is applied. We clean the panels thoroughly, removing wax, polish residue, grease, road film and any silicone from previous products. Any of these substances left on the paint will prevent the adhesive bonding properly and cause lifting, bubbling or peeling later.
Panel edges, door shuts, mirror backs and any recessed areas are all cleaned, not just the obvious flat faces. If there is any surface damage, we flag it before we start rather than cover it up. Installing film over a rust blister or a flaking edge will not hold, and it is not something we will do.
We come to your premises in Rushden to carry out the work. You do not need to transport the van anywhere. For the installation itself, we need a dry, reasonably sheltered area. Film applied in direct sunlight or in the rain will not adhere correctly, so we plan the visit for appropriate conditions.
Panel by panel, the film is applied using a combination of squeegee work and heat from a heat gun. The heat makes the film pliable enough to stretch into recesses, around curves and over door edges without trapping air or wrinkling. Each section is worked progressively to push air to the edges and ensure the adhesive contacts the paint uniformly.
Edges at door frames, wheel arches and bumpers are wrapped around and bonded in the door shuts or under the bumper lip wherever possible. This prevents the edge of the film from being visible or accessible to water and prevents lifting at the most vulnerable points. It takes more time and film, but the result is a finish that holds and looks clean from every angle.
Tricky points on most vans include the lower door swage line, the area around the sliding door rail (on panel vans), mirror caps and the rear step area. Each requires the film to be cut, relieved and re-laid so the finish lies flat without lifting or puckering.
Once the main panels are done, every edge, join and corner is gone over again. Any small lift or bubble that appeared during the initial application is worked out. Joins between panels are checked to ensure they are consistent and that the colour and pattern match across them.
The finished installation is inspected in good light from multiple angles and distances. What looks acceptable up close at an odd angle may look wrong from ten feet away when someone is reading your contact details. Both matter on a working trade vehicle.
We clear all off-cuts, packaging and waste from your premises. The van is wiped down with a clean, non-abrasive cloth to remove any fingermarks or residue from the installation process. At handover we run through how to look after the wrap: what to wash it with, what to avoid, and anything specific to the film type used.
Avoid pressure washing directly at edges and seams, particularly in the first week when the adhesive is still reaching full cure. Hand washing with a mild, non-solvent cleaner is the right approach for the long term. Automated car washes with rotating brushes are worth avoiding entirely; touchless drive-throughs are less aggressive but still not ideal.
We also carry out wrap removal, whether that is to replace an existing design, to sell the vehicle, or simply because the wrap has reached the end of its life. Removal is done carefully with a heat gun and appropriate tools to avoid damaging the paint underneath. On a vehicle where the original paintwork was sound and the film has been on for a reasonable number of years without being left to degrade, the paint typically comes away in good condition.
We design and print in-house, and we travel to you. If you are a sole trader or run a small fleet near Rushden, call us to talk through your brief and get a clear price for the full job, design to installation.
Also available
We wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsA full van wrap transforms your vehicle into a moving billboard across Northampton and beyond.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.