If your van's graphics are starting to look tired, faded or just plain wrong for your business, it's time to look at what's actually going on and sort it properly.
Van graphics work hard. They're out in the rain, the frost, the summer sun, and they take the daily knocks of a working vehicle. Most problems don't appear overnight - they build up gradually, and by the time you notice them properly, the damage is already undermining the professional image you're trying to project to every customer and passer-by in Kettering.
Knowing what to look for means you can act before the graphics become an embarrassment rather than an asset.
The most obvious sign is fading. Printed graphics lose their colour intensity over time, particularly on panels that face upward or south-facing when the van is parked. What started as a vivid brand colour can drift into a washed-out version of itself. If your van livery no longer matches your website, your workwear or your other branded materials, customers will notice the inconsistency even if they don't consciously register why.
Lifting edges are another common problem. Graphics are applied to a prepared surface, and when that preparation wasn't thorough, or when the application was done in cold or damp conditions, the adhesive bond at the edges can begin to fail. You'll see this first at corners, around door handles and along the bottom edges of panels where water and grit get in. Once an edge starts to lift, dirt and moisture get underneath and the problem accelerates quickly.
Bubbling under the film is a sign that air or moisture was trapped at the time of application, or that the original preparation missed contamination on the bodywork. Small bubbles can sometimes be managed, but larger ones distort the printed image and make the van look poorly finished.
Cracking or crazing across the printed surface happens when a cast vinyl has been applied over a complex curve or recess and the material has been stretched beyond its limits. It can also happen when a calendered (non-stretch) film has been used on areas that needed a more flexible material. The result looks like fine lines running through the graphic, particularly around door frames and wheel arches.
Ghosting - the outline of old graphics visible through or beneath new paintwork or a fresh wrap - is a problem that emerges when old graphics weren't properly removed before new work was done. The adhesive residue or the shadow of the old lettering shows through, especially in certain lights. It suggests corners were cut on the previous job.
Peeling prints on sections that see regular physical contact - around loading door edges, the cab door surround, the lower rear panel - point to either a material that wasn't suited to high-contact areas, or a laminate that's failing. Laminate is the protective layer applied over the printed graphic. Without it, or with a cheap version of it, the ink itself is exposed and will peel, scratch and abrade rapidly.
Most graphic failures come down to one of three causes: poor preparation, the wrong material for the application, or a rushed installation done in unsuitable conditions.
Poor surface preparation is the most common root cause. The van's bodywork must be cleaned of all grease, wax, polish, silicone residue and contaminants before any film goes on. Wax in particular is invisible to the eye but destroys adhesion. If a van has been cleaned regularly with a wax-based product - as most clean commercial vans are - the surface needs a proper decontamination wash and an IPA (isopropyl alcohol) wipe-down before application. Skipping this step means the graphics will lift, usually within months.
Wrong material choice matters more than many customers realise. Calendered vinyl is cheaper and works well on flat or gently curved panels. Cast vinyl is more expensive but conforms to compound curves, recesses and riveted surfaces without cracking or shrinking back. Using a calendered film on a van with strong curves or complex bodywork is a false economy - it will fail sooner and need replacing earlier.
Temperature and conditions at the time of application are critical. Vinyl adhesive needs a surface temperature of roughly 15-25°C to bond correctly. Applying graphics to a van that has been sitting outside on a cold morning, or in a draughty yard, is asking for trouble. The film goes on, but the adhesive never fully activates, and the bond is weaker from day one. We travel to your location to fit the graphics, and we'll always assess whether conditions are suitable before starting work.
Removal done poorly causes its own set of problems. Old vinyl that has been on a van for years bonds tightly and can, if removed without heat and patience, pull the paint with it - particularly on older vehicles or those with any touch-up paint that wasn't fully cured. Adhesive residue left behind then contaminates the surface for the next application.
We offer wrap and graphic removal as a separate service. Done properly, using the right heat and the right removal technique, the old material comes off cleanly and the bodywork is left in a condition that's genuinely ready for new graphics rather than just looking ready.
Beyond avoiding the warning signs above, it's worth knowing what a properly executed job delivers. The graphic should sit flat on the panel with no visible seam lifting, no bubbles and no distortion around curves. Colour should be consistent and sharp. Text should be legible at the distances your customers will be viewing it - a van is typically seen first at 10-20 metres, and the most important information needs to read clearly at that distance.
We design and print everything in-house at Northampton, which means we control the output quality directly rather than passing files to a third-party print house and hoping for the best. The design process involves thinking about how the graphics will read at speed, parked up and from multiple angles - not just how they look on a screen.
Van graphics range from simple cut vinyl lettering through to printed panels covering the doors, sides and rear, through to full or partial wraps that change the base colour of the vehicle entirely. Each approach suits different budgets and different brand ambitions. The right choice depends on what you need the van to do commercially and how long you plan to keep it in its current livery.
If you're a tradesperson or fleet manager in Kettering and your van's graphics are showing any of the warning signs above, give us a call and describe what you're seeing. We'll tell you honestly whether it's a repair, a partial refresh or a full replacement you need - and we'll come to you to do the work.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.