If your van is on the road in Kettering every day without your business name on it, you are missing thousands of impressions that cost you nothing extra.
A plain white or plain-coloured van is a wasted opportunity. Every time you park outside a job, pull up at a supplier, or queue in traffic, potential customers see a vehicle that says nothing about who you are or what you do. Van signwriting fixes that by putting your name, number and services in front of people who are already in the area where you work.
We design and print everything in-house at Van Wrapping Northampton, then come out to you in Kettering to apply the graphics at your premises or wherever the vehicle is kept. You do not need to drive to us.
If you already have signwriting on your van, there are clear signs that it is working against you rather than for you. Faded lettering is the most obvious one. Vinyl that was once a strong blue or red can bleach out to a washed-looking pastel after prolonged exposure to sunlight, and the moment it looks tired, it reflects badly on your business before a customer has even spoken to you.
Lifting edges are another tell. Vinyl that has started to peel at the corners or along a panel join lets moisture get underneath, and once water is trapped there the adhesive fails progressively. A small lift that is left alone will spread. At that point you are not just looking at a repair, you are looking at a full removal and re-application.
Bubbling across the face of a graphic is usually caused by one of two things: either the surface was not prepared properly before the vinyl was laid down, or a cast vinyl was not used where the panel has a compound curve. Air has nowhere to go on a curved surface unless the film is flexible enough to conform to it without trapping pockets. If the bubbles are small and scattered, they may have appeared during application and were never going to settle out. If they appear later, moisture or contamination underneath the film is usually the cause.
Cracking or crazing in the print layer is a sign that the laminate protecting the printed graphic has failed or was never applied. Unlaminated printed vinyl has a short outdoor life. Direct rain and road grime work into the ink layer and the image breaks down. Any printed signwriting applied to a working van should have a protective laminate over the top of it.
Poor surface preparation before application is behind a large proportion of signwriting failures. Panels need to be degreased properly, and any silicone residue from polish or detailer products needs to be removed. Silicone is invisible and it stops vinyl adhesive bonding correctly. A van that has been regularly machine-polished before signwriting is applied needs careful preparation.
Applying vinyl in cold conditions causes problems too. Below around 10 degrees Celsius, the adhesive does not flow into the surface texture of the paint properly, and the bond is weaker from the start. Work done in an unheated yard in winter is at higher risk of early failure than work done in a controlled indoor environment or during warmer months.
Cheap cast vinyl or calendered vinyl used in the wrong application is another common source of failure. Calendered vinyl is stiffer and is suited to flat or very mildly curved panels. On doors with deep recesses, wheel arches, or bumpers with compound curves, it will lift at the stress points. Cast vinyl is thinner, more conformable, and costs more, but it is the right material for those areas.
Finally, a design that uses very fine lettering or thin strokes at small sizes will not hold up as well as bolder, simpler lettering. Thin characters are harder to weed cleanly and the edges have less adhesive contact area. At reading distance from a moving vehicle, fine fonts lose legibility anyway, so there is a practical and a durability reason to favour clean, bold lettering.
Not all problems are physical. Sometimes the signwriting is in good condition but it still is not working. If people cannot read your number from across the road, the font size or colour contrast is wrong. White lettering on a silver van is a common culprit. The two colours bleed into each other at any distance and the number becomes illegible. Dark lettering on a light van, or light lettering on a dark background with enough contrast, is what actually gets read.
Cluttered designs that try to include too much information lose the most important detail, which is usually the phone number. A van is not a website. Someone driving behind you has three to five seconds to take in what matters. Name, what you do, number. That is the hierarchy. Anything else is secondary.
If your current van signwriting has any of the above issues, that is the point to call us and discuss a replacement. We can remove existing vinyl cleanly as part of the job, check the panel condition underneath, and re-apply fresh graphics. All work is carried out at your location in or around Kettering.
Cast vinyl used for cut lettering typically performs well for a number of years outdoors on a vehicle, provided the surface was prepared correctly and the vehicle is kept reasonably clean. Printed graphics with a protective laminate also have a good outdoor life under normal working conditions. Vans that are parked in direct sun all day will see faster colour shift than those garaged overnight, but for most tradespeople using their van daily, good-quality applied vinyl should give several years of presentable service before it starts to look tired.
That said, we do not make specific performance claims on our own behalf, and the lifespan of any signwriting depends on the conditions the vehicle faces day to day.
If your van is looking faded, your lettering is peeling, or you have never had signwriting applied and want to know what is involved, call Van Wrapping Northampton directly. We will come to you in Kettering, assess what is needed, and talk you through the options.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.