If your van, lorry or fleet vehicles in Kettering need professional graphics, spotting the warning signs early saves you money and keeps your branding looking sharp on the road.
Most tradespeople and fleet managers notice something is wrong with their vehicle graphics long before they act on it. A peeling edge here, a colour shift there. By the time it looks really bad, the problem has usually been building for a while. Knowing what to look for means you can deal with it before it hits your professional image or gets more expensive to fix.
Vehicle graphics are a working tool. They put your name, number and trade in front of potential customers every time you park up or drive through Kettering. When they start to fail, that tool stops working as it should.
The most common early failure point is at the edges and corners of printed panels or cut vinyl lettering. You will often see a small lift at the bottom edge of a door graphic or at the corner of a rear panel. This is not just cosmetic. Once the edge lifts, water gets underneath, and the adhesive bond breaks down progressively from that point outward.
Lifting edges are usually caused by one of three things: the surface was not clean or dry enough when the graphics were applied, the material itself was a low-grade cast or calendered vinyl that has aged and shrunk, or the vehicle has been through a lot of automated car washes with high-pressure jets. A good application starts with a properly degreased, panel-wiped surface and uses material suited to the job, applied at the right temperature.
Printed vehicle graphics use UV-resistant inks, but all printed colour fades over time with sun exposure. If your fleet vehicles were all lettered at the same time and you are noticing that some look noticeably duller or more washed-out than others, the culprit is usually how they are stored. A vehicle parked outside, facing south, in direct sun all day will fade faster than one kept in a yard or garage when not in use.
Colour shift can also happen when a laminate protective layer starts to delaminate. The laminate is applied over the printed surface to protect it from UV, fuel splash and minor abrasion. When it starts to fail, often visible as a cloudy or milky patch in the print, the colour underneath degrades quickly. This tends to happen on vehicles that have been exposed to heavy weather without the protection of quality over-laminate.
If you are managing a fleet in and around Kettering, mismatched branding across different vehicles sends the wrong signal to customers. A van that looks fresh next to one that is visibly faded suggests a business that is not on top of things. Replacing graphics on the worst performers first is usually the right call.
Small bubbles that appear shortly after a new application sometimes work themselves out within a few days, especially in warmer weather. Bubbles that persist, grow or appear on older graphics are a different matter. They mean air or moisture has found its way between the vinyl and the vehicle surface and cannot escape.
Silvering is the name given to the silvery or hazy patches you see when the vinyl has partially lifted but not yet fully peeled. It is especially visible on gloss or metallic graphics. Once silvering appears, the material has lost its adhesive grip in that area and will not re-bond without professional attention.
Both bubbling and silvering can be caused by poor application technique, by applying in cold weather without allowing the vehicle and material to reach a suitable working temperature, or by trying to apply graphics over existing damaged paintwork. Pitted or rusty panels, old decals not properly removed or repaired paint edges all create a surface that vinyl cannot bond to reliably.
Calendered vinyl, the cheaper and thicker grade of film sometimes used for temporary or short-life graphics, has a relatively short outdoor lifespan. As it ages it loses flexibility and becomes brittle. You will see it crack along its length, often following the direction the film was originally rolled. On a large flat panel this produces a network of fine cracks across the surface.
Cast vinyl is more dimensionally stable and does not shrink or crack in the same way, making it the right choice for full wraps, complex shapes and long-term installations. If your graphics are cracking, the material used was likely not suited to the duration or the shape of the panels it was applied to. Replacing cracked graphics is straightforward, but it does mean removing all the old material properly before new graphics go on.
When old graphics are removed badly, they leave adhesive residue and sometimes a visible ghost of the original graphic in the paintwork below. This happens when vinyl is left in place too long and the adhesive cures fully into the paint, or when removal is rushed without using heat to soften the adhesive. Proper removal uses a heat gun or steamer, slow controlled peeling and an appropriate adhesive remover to clean the surface afterwards.
If you have bought a used van for your business in Kettering, check carefully for ghosting from previous lettering. It is sometimes visible only in certain light. Having those remnants removed professionally before new graphics go on will give a far cleaner result.
Beyond material quality and application standards, the following factors accelerate the deterioration of vehicle graphics:
None of these are unavoidable in day-to-day trading, but being aware of them means you can extend the life of a good installation considerably.
We design and print in-house, which means we control the quality of the material and the print from start to finish. We also carry out wrap removal, so if you need old graphics stripped before new ones go on, that is part of what we offer. It is worth checking that any installer you use is insured. We come to you, carrying out the work at your premises or wherever the vehicle is based.
We work on cars, vans, lorries, trailers and full fleet vehicles. Whether you need a single van lettered for a sole trader starting out, or a consistent look across multiple vehicles for a growing business, the same design and print process applies.
If you have spotted any of the warning signs above on your vehicle or fleet, call us to arrange a look at what you have got and talk through the options.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.