If your fleet vehicles need wrapping or existing wraps need attention, here is what Duston operators can usefully do before we arrive - and what to avoid doing yourselves.
Fleet wrapping puts your brand across every vehicle in your operation using printed or cut vinyl film applied to the vehicle's panels. The process covers design, print and fitting. When comparing providers, it helps to ask whether all three are handled by one team, so you deal with one contact from start to finish. We come to your site in Duston or nearby to carry out the fitting - your vehicles stay where they are.
The result is a consistent look across your fleet: same colours, same logo placement, same contact details on every van. For tradespeople and small business operators, that consistency is what turns a fleet of vehicles into a recognisable brand presence on the road.
When choosing a fleet wrapper, check that they are insured and ask whether they work at your premises or need your vehicles taken to a workshop. For fleet work in Duston and across Northampton, on-site fitting means less disruption to your operation while work is under way.
Between making contact and us arriving on site, there is usually a period while we confirm the design, print the film and schedule the fitting. That window is not wasted time - there are things you can do in that period that directly affect the quality and speed of the finished job.
None of this is complicated, but it is worth knowing about because a vehicle that arrives for fitting in the wrong condition slows everything down and can affect the result.
Vinyl film adheres to paint, not to dirt, grease, wax or traffic film. A vehicle that arrives for wrapping with a layer of road grime, old polish or diesel residue on the panels will produce a poorer bond and a shorter-lasting result. Wash the vehicles properly - not just a quick rinse, but a proper clean that removes wax and grease from the panel surfaces.
Use a mild detergent rather than a wax-based car shampoo. Wax shampoos leave a residue on the paint surface that interferes with film adhesion. If your vehicles have recently been polished or valeted, tell us - we may need to wipe panels down with an appropriate surface preparation product before we start.
Walk around each vehicle and note any rust spots, chips where the paint has lifted, or areas where the lacquer is peeling. These need addressing before the film goes on, because wrapping over damaged paint traps the problem underneath and shortens the life of the wrap. You do not need to fix every stone chip, but lifting paint or surface rust should be dealt with first.
Let us know what you find when we confirm the job. It allows us to plan accordingly and means there are no surprises on the day that push the schedule back.
We need room to work around each vehicle. A van parked between two others with six inches of clearance on each side is difficult and slow to work on. If you can arrange for the vehicles being wrapped to be parked with enough room to open all doors fully and walk around them, the job goes faster and the result is better.
If work is being done outdoors, choose a spot that is sheltered from direct wind where possible. Vinyl film is manageable in normal outdoor conditions, but working in a stiff breeze with large sections of film is awkward and slows the fitting process.
If you are bringing us a new design brief, have your logo files ready in a vector format (AI, EPS or high-resolution PDF). A logo supplied as a small JPEG from your website will not reproduce well at the size needed for van panels. If you are not sure what format your logo file is in, check with whoever designed it originally. Supplying the right file from the start avoids a round of back-and-forth that delays the design proof stage.
If you already have brand guidelines - specifying Pantone or CMYK colour references - pass those to us at the start. We print in-house and we work to match your brand colours as closely as the print process allows.
This section is not about doubting your ability. It is practical guidance based on what commonly goes wrong when people try to handle part of the process themselves before the professional arrives.
If your vehicles have existing wraps that need to come off before the new film goes on, leave that to us. Wrap removal requires heat applied at the right level to soften the adhesive without damaging the paint underneath. Cold removal, or removal with the wrong tools, pulls paint off the vehicle. We carry out wrap removal as part of our service - it is not a separate hassle, it is included in the job.
A common problem is operators peeling back a corner of a failing wrap to check the paint condition, then finding the paint comes with it. If the wrap is old and the adhesive has bonded aggressively to the paint, any attempt to remove it without proper technique and heat will cause paint damage. Leave it alone until we are on site.
In particular, do not wax, polish or apply any spray detailer to the vehicles in the days before we arrive. These products leave a residue that is difficult to remove completely and that reduces adhesion. A clean, unpolished paint surface is what we need. If your fleet goes through a regular valet programme, pause it for the week before wrapping is scheduled.
If part of an existing wrap is lifting or has bubbled, resist the urge to press it back down with tape or glue. General-purpose adhesives are not compatible with wrap film and will make the area harder to repair or remove. If an edge is lifting, keep the vehicle out of heavy rain where possible and contact us to arrange a repair visit.
A common mistake when providing brand assets is assuming that whatever works on a letterhead will automatically work on a van. A busy design with small text reads well at A4 and is completely illegible at four metres. If you have a view on what the wrap should look like, share it with us at the design stage - that is the right moment to test it. After print is not.
On the day we arrive, the vehicles should be clean, accessible and parked with enough space to work. We bring all materials and equipment to site. Fitting time depends on the size of the vehicle and the scope of the wrap, and partial wraps and signage jobs are usually quicker than full wraps. For a fleet of multiple vehicles, we work through them in a planned sequence to minimise the number of vehicles off rotation at any one time.
Once fitting is complete, we do a final visual check on each vehicle before we leave. If anything needs attention - a small air pocket, an edge that needs re-pressing - we deal with it on the day.
Call us to start the conversation. Tell us how many vehicles you have, what your brand looks like and when you need the work done. We will come to your site in Duston, assess the vehicles and give you a clear cost per vehicle. The earlier in the process you involve us, the smoother the job goes.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsA full van wrap transforms your vehicle into a moving billboard across Northampton and beyond.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.