Covering Northampton and the surrounding area Monday to Friday 9:00am - 5:00pm Get a quote

Lorry and HGV Graphics in Duston - What to Do While You Wait (and What to Leave Alone)

If you're waiting for lorry or HGV graphics to be fitted near Duston, there's useful preparation you can do beforehand - and a few things that cause real problems if you tackle them yourself.

5.0 from 9 Google reviews Est. 2020 Quoted in writing first Nothing printed until you sign off the proof Fitting arranged at your site

HGV Graphics - What We Do and How It Works

We fit full-colour graphics and vinyl lettering to lorries, artics and HGVs. The work ranges from cab door lettering and fleet numbering through to full printed trailer wraps. We design and print in-house, which means your files, colours and layouts stay under one roof from start to finish. We come to you - the work is done at your premises or yard, so there's no need to take your vehicle out of service to visit a workshop.

What You Can Do Before the Appointment

There's a reasonable amount of useful preparation you can do in the days before an HGV graphics appointment that makes the installation go more smoothly and reduces the chance of problems developing later.

Clean the vehicle thoroughly. This is the single most useful thing you can do. Road grime, diesel soot, salt deposits and traffic film all affect how well vinyl adheres to a surface. Wash the trailer sides, cab doors and any other areas in scope with warm water and a mild detergent. Rinse well and allow the surfaces to dry completely. If your depot runs vehicles through an automated truck wash, do so at least 48 hours before the appointment so the surface has time to dry out fully.

Remove any loose items near the work area. Lorry cabs and trailer sides collect oil cans, tie straps, curtain hooks, side skirt fixings and all kinds of roadside ephemera. Clearing the area gives the installer room to work and reduces the risk of anything getting knocked over onto a freshly applied panel.

Make sure the vehicle will be accessible throughout. The installer needs access to both sides and the rear in most cases. If your yard is tight, let us know in advance and we'll work out a plan. Trying to do one side and come back for the other because space runs out is not ideal and can affect consistency.

Have your design files ready if you're supplying them. If your business has brand guidelines, logo files in a vector format (AI, EPS or PDF rather than a JPG), and colour references, have these ready to share before the design stage. It speeds things up considerably. If you need us to design from scratch, tell us that at the booking stage so we can allow the right time.

Surface Contamination - the Hidden Problem

The most common reason for vinyl failing prematurely is surface contamination at the time of application. This isn't about visible dirt - it's about oils, waxes, silicone residues and invisible chemical films that washing alone may not remove.

If your vehicle has been through a polish or wax treatment recently, or if the trailer sides have been treated with any kind of protective coating, tell us before the appointment. These need to be removed with a panel wipe before any vinyl is applied. Silicone in particular causes vinyl to lift at the edges within days of application, and by then the film is already installed.

Similarly, if any bodywork or paint repairs have been carried out on the vehicle recently, check that the paint has cured fully before graphics are applied. Fresh paint (less than four weeks old as a rough guide) and vinyl film don't work well together.

What Not to Do Yourself

It's tempting to get started, particularly if you're waiting a few days for an appointment slot and you want the vehicle looking smart as quickly as possible. Some things are fine. Some are not.

Do not attempt to remove old graphics yourself using a heat gun if you haven't done it before. Vinyl removal on large panels looks straightforward, but getting the heat wrong - too hot, too concentrated, held in one place too long - can lift, crack or blister the paint underneath. On an older vehicle with surface rust under the paint, it can expose and worsen underlying damage. On a leased vehicle, it can create a bill that far exceeds the cost of professional removal. We offer removal as part of the process, and it's priced into the job.

Do not try to re-adhere lifting graphics with general-purpose adhesives, superglue or silicone sealant. These contaminate the substrate and make the area impossible to work on properly. Any adhesive residue under a new graphic causes the vinyl to fail at that spot, often as a bubble or blister within weeks.

Do not clean the surfaces immediately before the appointment with solvent-based products unless you've been specifically advised to do so. Products like white spirit, acetone or petrol can leave a residue that interferes with adhesion even when they appear to have dried. A simple mild detergent wash and a thorough rinse is the right preparation.

Do not apply masking tape or stickers to surfaces in the work area. Any adhesive left on the surface - even from low-tack masking tape - creates a problem for the installer and can affect the finished result.

On the Day of Installation

Have the vehicle in position and ready when the installer arrives. The work area should be sheltered from rain if possible - vinyl application in wet conditions is difficult, and water on the surface during installation can trap moisture under the film. If your yard is exposed, let us know and we'll plan accordingly.

Try to keep other vehicles and foot traffic away from the work area during installation. It reduces the risk of dust settling on a freshly applied panel and prevents accidental contact with wet vinyl before it's fully positioned.

After the Installation

Avoid pressure washing for the first few days while the adhesive cures. Avoid folding curtainsider panels aggressively during the same period. These are small constraints that make a real difference to how the graphics bed in.

Operators near Duston can book a vehicle visit at your premises. Call us to discuss the job, run through what preparation is needed for your specific vehicles, and get a clear picture of what's involved before we arrive.

Why use us in Duston

  • Your design shown on your vehicle before printing.
  • Graphics designed and printed by us.
  • We fit at your premises in Duston.
  • We are insured.

Lorry and HGV Graphics in Duston?

Phone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.

Call Quote