If your minibus graphics in Duston are booked in or on order, here is what you can usefully do while you wait - and what is likely to make things worse if you try it yourself.
Vinyl graphics on a minibus range from simple cut lettering and door logos to full printed wraps covering every visible panel. The work involves design, print, preparation of the vehicle surface, and fitting - each stage affecting the quality of the finished result. We handle design and printing in-house at Van Wrapping Northampton, and we travel to your site to do the fitting, so the vehicle stays where you are.
The work is done on your premises or at an agreed location, without you needing to arrange drop-off at a workshop.
Between booking the job and the day we arrive, there are things worth doing that will make the installation go more smoothly - and things worth avoiding that could complicate it.
Surface preparation is part of what we do before fitting, but arriving with a vehicle that is caked in road grime, salt residue or old bird droppings adds time and, in some cases, risks. A vehicle that has had a proper hand wash - not a pressure blast, just a thorough soapy clean and rinse - is in a better state to work with. Focus on the panels that are going to be graphic areas: sides, rear doors, bonnet if relevant.
Avoid waxing the vehicle before we arrive. Wax and silicone-based products on the paint surface interfere with vinyl adhesion. If the vehicle has recently been polished with a wax product, tell us - we will need to degrease those areas before fitting.
Walk around the vehicle and note any chips, corrosion spots, peeling previous paint or areas where the paint surface is uneven. Vinyl applied over damaged paint will show the damage underneath and will not adhere properly along edges that are lifting or flaking. Where paint damage is significant, it needs addressing before graphics are fitted, not after.
You do not need to fix these before our visit - but knowing where they are, and telling us in advance, means we can discuss the best approach rather than finding them on the day.
If you have an existing logo, specific brand colours or a website, have those assets ready to share before the design stage. A vector file - AI, EPS or high-resolution PDF - gives us the cleanest starting point. If your logo only exists as a small JPEG on a business card or old leaflet, we can often redraw it, but it helps to know that upfront rather than the day before fitting.
If you are unsure what files you have, check with whoever designed your original branding. The file type usually shows in the filename extension.
The clearer your brief, the faster the design process and the fewer rounds of changes. A useful brief answers a few simple questions: What is the vehicle used for? Who sees it, and where? What do you want people to do when they see it - call a number, visit a site, recognise the livery? Are there other vehicles in the fleet that need to match?
These questions shape design decisions in ways that matter. A minibus used for school transport, a private hire shuttle and a sports club supporter coach all have different audiences and priorities, even if the basic brand is the same.
If you have already had an initial discussion with us, photographs of the vehicle from each side, the rear and the front are useful reference during the design stage. They help confirm panel layout, window positions, door shuts and any body features - stepped rooflines, roof vents, raised ribs - that affect how a design needs to be adapted.
Standard minibus body dimensions are known quantities for us, but if your vehicle has had bodywork modifications or is a less common body type, photographs help avoid surprises on the day.
If the vehicle has existing graphics that need to come off before the new ones go on, leave that to us. We offer wrap removal as a service. Attempting to pull old vinyl off without experience, without the right heat tools, or in cold conditions risks pulling the paint with it - particularly on older vehicles where the paint bond to the metal may be less than perfect.
Adhesive residue left behind after amateur removal is also a problem. It is sticky, picks up contamination, and significantly complicates the surface preparation for new graphics. The adhesive removal products available to consumers are rarely strong enough for the task and can themselves leave residue or stain the paint.
Magnetic signs and self-adhesive tape leave marks and sometimes pull the surface coating slightly, particularly on vinyl-wrapped panels or on metallic paints. If you are using temporary signs in the gap before the permanent graphics are fitted, keep them away from the specific panel areas that will be covered. On a bare paint vehicle this matters less, but on any vehicle with existing film it can cause problems.
Fresh paint needs time to cure fully before vinyl is applied to it. The standard advice is to allow at least 30 days for a standard air-dried paint job, longer for areas that have been heavily filled or primed. Vinyl applied over fresh paint can trap solvents still off-gassing from the paint, which causes bubbling. If any panel has been resprayed, tell us and confirm the date it was done.
Some operators arrange a full valet or paint protection treatment while they are waiting for graphics - check what that treatment includes. Ceramic coatings are specifically designed to prevent anything bonding to the paint surface, which is exactly the opposite of what is needed for vinyl adhesion. If a ceramic coating has been applied recently, vinyl graphics may not adhere properly at all. Tell us before we arrive if this is the case.
Have the vehicle available and reasonably protected from direct sun and rain. Fitting in full sun on a hot day makes the vinyl difficult to handle and work. Fitting in rain creates contamination risk during the process. An indoor space - a garage, a depot bay, even a large covered area - is ideal. If none of that is available, an overcast day in a sheltered spot is workable. Tell us the site conditions when you book and we can discuss what works.
Allow access to a power point for heat tools. We carry our own equipment, but a power source nearby makes the job faster and more comfortable in cold conditions.
We serve operators in Duston and across Northampton - school transport, private hire, sports clubs, shuttle services and small fleet managers. If you are ready to book or just want to talk through what you need and get a clear quote, call us directly and describe your vehicle and your requirements.
Also available
We design, print and fit full or partial van wraps in Northampton, working at your premises so your vehicle never needs to leave your site.
See detailsWe wrap commercial vehicles of all types across Northampton, from small vans to large panel vans and specialist bodies.
See detailsWe design, print and fit branded wraps across entire vehicle fleets in Northampton, ensuring every vehicle in your fleet looks consistent.
See detailsPhone us or fill in the form. A few details about the vehicles are enough for us to start on a written quote.